Smok ALIEN KIT 220W box KIT E-Cigarette

Nuovo prodotto

Smok ALIEN KIT 220W box KIT E-Cigarette

Maggiori dettagli

Questo prodotto non è più disponibile

69,80 € tasse incl.

Scheda tecnica

Batteria Non inclusa
Capacità atomizzatore 3 ml
Power Range 1W - 220W

Dettagli

flavordust-smok-alien-220-01.jpg

flavordust-smok-alien-220-19.JPG


THE KIT INCLUDES

flavordust-smok-alien-220-03.jpg

SPECIFICATIONS

flavordust-smok-alien-220-04.jpg

flavordust-smok-alien-220-05.JPG

flavordust-smok-alien-220-06.JPG

flavordust-smok-alien-220-07.JPG

MORE DETAILED VAPING DATA

The clear and precise OLED screen offers an entirely new operation interface. More vaping data for you, such as VW/TC MODE, vaping effect, voltage, battery life, resistance value etc.
Tips: There is a transparent protective layer on this side, you can rip it

flavordust-smok-alien-220-08.jpg

flavordust-smok-alien-220-09.JPG

SPECIFICATION OF TWO EDITIONS FOR ALIEN MOD

There are A and B two versions of Alien220 mod with the same function as for its improvement of MCU. Edition A will display V1.x.x (newest is V1.2.11) when powered on, while edition B will display VB1.x.x (newest is VB1.0.2). Please make sure the device version and download the corresponding version before firmware upgrading, for A and B version is totally different and cannot be employed universally. (You can brush up the device with the correct version if incorrect version is upgraded, and unmatched firmware upgrading is not recommended as wrong update can result in a brick device,you can flash your VB version Alien by http://www.smoktech.com/support/upgrade/toolsandfirmware/ispalien )

flavordust-smok-alien-220-10.jpg

COMPONENTS

flavordust-smok-alien-220-11.jpg

flavordust-smok-alien-220-12.JPG

flavordust-smok-alien-220-13.jpg


ADJUSTABLE AIRFLOW SYSTEM

Bring you an extremely open draw. Airflow can be adjusted freely by turning the ring at the base of atomizer.

flavordust-smok-alien-220-14.jpg

flavordust-smok-alien-220-15.JPG

BUILDING THE RBA

1. Be sure your hands are clean.
2. Disassemble the RBA deck.

flavordust-smok-alien-220-16.jpg



3. Install and seat the pre-wrapped coil. Place the coil between the posts and wrap the ends around the screws and tighten them to secure the coil. Be sure the coil is fixed in the center and that the coil is lined up with the airflow hole.Make sure that the coil is NOT touching the base.
4.Clip the excess leads from your coil.

flavordust-smok-alien-220-17.jpg



5.Prepare your cotton, not too much but also not too little.
6. Insert the the cotton and thread it through the middle of the coil.
7. Cut the ends of the cotton at an angle, again not too long but not too short.

flavordust-smok-alien-220-18.jpg


8. Prime your cotton by wetting it with e-liquid and adjust it’s position. (Be sure to check the resistance of your coil before placing it under load. Furthermore check the coil’s resistance periodically throughout it’s usage to monitor for any changes.)

Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi una recensione

Smok ALIEN KIT 220W box KIT E-Cigarette

Smok ALIEN KIT 220W box KIT E-Cigarette

Smok ALIEN KIT 220W box KIT E-Cigarette